Skip to content

My Lil' Mule

The adventures of a Jeep and its driver.

Tag: weld

Posted on February 10, 2020August 11, 2022

Starting to get more done to the shop again.

Starting to get more done to the shop again. Ran a couple 220v circuits for each of the welders plus a 110v circuit for some much needed outlets. Changed my plans a bit and swapped the welders to the east wall so the runs are shorter.
.
.
.

Instagram Source

Posted on February 8, 2020August 11, 2022

Decided to raise the workbench up to a total of 40”

Decided to raise the workbench up to a total of 40”. Seemed like it was going to be tall, but I really like it. It’ll match up well with the soon to be ordered @weldtables welding table.
.
.
.

Instagram Source

Posted on January 21, 2020August 12, 2022

Stacking those dimes!

Stacking those dimes! 😂😂😂 Now is I can only do this more than just this 1 inch of weld. LOL!
.
.
.

Instagram Source

Posted on December 12, 2019August 12, 2022

Got this old Sears/Devilbiss air compressor restored.

Got this old Sears/Devilbiss air compressor restored. Replaced all the gaskets and piston rings. New controller and regulator valve. Fresh coat of paint. Super quiet compared to my other compressor. And this one can hold 7.4cfm@125psi.
.
.
.

Instagram Source

Posted on December 5, 2019August 12, 2022

Trying out some 7018 on the new welder.

Trying out some 7018 on the new welder. Haven’t run any SMAW for 2 1/2 years and that was only once or twice. This machine makes it seem too easy.
.
.
.
.
.

Instagram Source

Posted on March 11, 2019August 14, 2022

Making lots of progress on the workshop.

Making lots of progress on the workshop. Concrete is set and cleaned and even managed to get the man doors and the overhead door installed. .
.
.
.

Instagram Source

Posted on March 1, 2019August 14, 2022

Almost there.

Almost there. A little more troweling and it will be time to sit back and watch it cure. Hopefully the heater will do what it needs to and keep the shop above freezing for the next couple of nights. .
.
.
.

 

Instagram Source

Posted on February 28, 2019August 14, 2022

Almost ready for concrete.

Almost ready for concrete.
.
.
.
.

Instagram Source

Posted on February 28, 2019August 16, 2022

Getting a rocky start to the day.

Getting a rocky start to the day.

Instagram Source

Posted on February 24, 2019August 16, 2022

Framing a small workshop in 30 seconds.

Instagram Source

Posts pagination

Previous page Page 1 Page 2 Page 3 Page 4 Page 5 Next page

Details

  • Affiliate Disclosure
  • Jeep JK Details

Jeep JK Build Chronology

Blog

Recent Posts

  • Machining Carbide Insert Tool Holders with my Shaper for a BXA Tool Post on a South Bend Lathe
  • Adding a Servo Motor to the DIY DRO
  • How Difficult is it to Add a Quick Change Tool Post to the 14-1/2″ South Bend Lathe?
  • Walker Turner Drill Press Table Elevating Rack
  • Custom Walnut Storage Case for my 18″ Denis Foster Straight Edge

Archives

Categories

  • Facebook
  • Twitter
  • Instagram
  • YouTube
  • Patreon
  • Rumble
  • Email

Meta

  • Log in
  • Entries feed
  • Comments feed
  • WordPress.org
Proudly powered by WordPress
My Lil' Mule
Proudly powered by WordPress Theme: Twenty Seventeen.